|
MENU
|
 /TARE
|
DESCRIPTION
|
|
INPT
Input
Type
|
Show
input choices:
|
|
100m
|
100mVdc |
|
▒50m
|
50mVdc |
| 10
V |
10Vdc |
| ▒5
V |
5Vdc |
| 0-20 |
0-20mAdc |
|
|
DEC.P
Decimal Point
|
Show
current decimal point position.
|
FFFF.
FFF.F
FF.FF
F.FFF
|
RD.S.O
(Reading Scale & Offset)
Enter new value
and show "RD 1"
Enter new value
and show "IN 2"
|
Show
IN 1 and prior value entered.
Scroll to the next digit to the right
Show prior value entered.
Scroll to the next digit to the right.
Show RD 2 and prior value entered.
Scroll to the next digit to the right.
|
Change the value of the flashing digit.
Change the value of the flashing digit.
Change the value of the flashing digit.
|
|
RD.CF
(Reading
Configuration)
|
R.1=
R.2=
R.3=
R.4=
|
R (Ratiometric Reading)
N (Non-ratiometric reading)
0 (1╡V resolution for unipolar & 5╡V resolution for bipolar)
1 (2╡V resolution for unipolar & 10╡V resolution for
bipolar)
2 (3╡V resolution for unipolar & 15╡V resolution for
bipolar)
3 (5╡V resolution for unipolar & 25╡V resolution for
bipolar)
4 (10╡V resolution for unipolar & 25╡V resolution for
bipolar)
Note: 3 ╡V resolution means if your input is 0-30mV,
at 30mV the display shows 9999.
F (Filtered value)
U (Unfiltered value)
G (Gross/Net Display)
P (Peak Display)
|
|
S1.CF
Setpoint
1 Configuration
|
S.1=
S.2=
S.3=
|
A (Active above)
B (Active below)
U (Unlatched)
L (Latched)
N (Net Reading)
G (Gross Reading) |
|
S2.CF
Setpoint
2 Configuration
|
S.1=
S.2=
S.3=
|
A (Active above)
B (Active below)
U (Unlatched)
L (Latched)
N (Net Reading)
G (Gross Reading) |
|
S1.DB
Setpoint 1 Deadband
|
Press
to scroll to the next digit to the right.
|
Press to change the value of the flashing digit |
|
S2.DB
Setpoint 1 Deadband
|
Press
to scroll to the next digit to the right.
|
Press
to change the value of the flashing digit |
|
OT.CF
Output
Configuration
|
0.1
0.2
0.3
|
E (Analog output is enabled)
D (Analog output is disabled)
C (Analog output is current)
V (Analog output is voltage)
N (Net Reading)
G (Gross Reading) |
| Notes:
1) if 0.2 = V, then you may select your analog output to be
0-10 V or 0-5 V by accessing submenu 0.5 |
|
OT.S.O
OUTPUT
SCALE AND OFFSET
Enter new value and show "OUT1"
Enter new value and show "RD 2"
Enter new value and show "OUT2"
|
Show
RD1 and prior value entered
Scroll to the next digit to the right
Show prior value entered.
Scroll to the next digit to the right
Show prior value entered.
Scroll to the next digit to the right
|
Change the value of the flashing digit
Change the value of the flashing digit
Change the value of the flashing digit
|
|
LK.CF
LOCK OUT CONFIGURATION
|
RS=
SP=
L3=
|
E (Enable RESET button in the run mode)
D (Disable RESET button in the run mode)
E (Enable setpoint changes)
D (Disable setpoint changes)
0 (SETPTS button display setpoint values)
1 (SETPTS button display software ôv.-03ö version) |
Home
TOC 
Back 
Next
/NT/GRS